Spooling Up
Unlike monofilament, PowerPro will not stretch on the reel and cling to the
barrel. This can result in line sliding around the barrel, which can seem like
a problem with your drag mechanism. Rest assured, your equipment is fine. To
avoid slippage, attach PowerPro to your spool using one of these methods:
1) If your reel has a hole or knob on the barrel, use it.
2) Leave at least 5 to 10 yards of monofilament on the reel (enough to cover
the bottom of the spool) before attaching PowerPro with a Uni to Uni
splice.
3) Put a piece of compressible tape on the barrel before attaching PowerPro.
Setting the Hook
Anglers on Saturday morning TV shows often set the hook in bass like
Samurai warriors beheading the enemy. This may be a fine technique with
monofilament line, but PowerPro doesn't require such a violent motion. When
you get a strike, relax; a gentle snap of your wrist will set the hook.
Because PowerPro doesn't stretch like nylon lines, you won't get that
rubber-band effect. Every inch you move your rod tip equals an inch of
movement at the lure.
Setting your Drag
PowerPro lines are so small for their strength that you may be tempted to
set your drag higher than normal, but remember, your rod or reel may not be
designed to handle the same unbelievable loads as your line. To make full use
of PowerPro's amazing sensitivity without risking damage to your equipment,
try one of the following tips:
1) Set your drag to match the weakest component in your tackle system.
2) Set your drag to match the size of mono line you would normally use.
3) When using ultralight equipment or line (10- or 20-lb. test) set your
drag to no more than 1/3 of the line's rated strength. You can check the
drag with a fish scale.
At lower drag settings, a little extra line may pay out at the hookset,
compensating for PowerPro's lack of stretch.
Fish with Spinning Reels
For optimal PowerPro performance on your spinning reel, we recommend
closing the bail manually. While your bait is falling, pull on the line to
make sure it is seated firmly on the reel, then begin your retrieve.
Cutting PowerPro
PowerPro is extremely strong, and nail clippers won't cut it. We recommend
sharp scissors such as
Fiskars® for kids, which are inexpensive,
easy to find, and have blunt ends to protect your pockets.
Coloring PowerPro
Spectra Fiber is an especially dense material that cannot be permanently
dyed. The color simply encapsulates the line and will wear away with time.
This is normal and does not affect the strength or performance of the line. To
re-color your PowerPro line, simply use a permanent magic marker in whatever
shade you prefer.
Retie your Line
Although PowerPro is extremely strong, it isn't indestructible. If the line
starts to look frayed, especially after fishing around structure, it's
probably time to cut off the worn section and retie. This way your line will
always perform at rated strength.
Repack your Line
If your line starts to feel soft or mushy on the reel, especially when
fishing with light baits, you should repack your reel. Make an extra long cast
or let the line out behind your boat, then reel it in while holding the line
taut with your fingers. This will improve casting performance and keep the
line from "digging in" after a solid strike.
Using a Monofilament Leader
Attaching a monofilament leader to your PowerPro line may prove useful in
the following situations:
1) When bait or jig fishing requires extra finesse, especially in clear
water, use a 3-foot monofilament leader to cut down on line visibility.
2) When fishing for species that strike hard and fast, use a monofilament
shock tippet. For close-in situations such as bait fishing, try a 3- to
10-foot tippet. For big game applications, you may want to use up to 100
yards or more.
CAUTION:
PowerPro is remarkably thin and strong. To avoid injury, never wrap it
around your fingers or hands. If you need to break off the line, wrap it
around a solid object and pull.
Which PowerPro line is right for me?
Light Tackle Applications
Select a PowerPro line similar in diameter to the monofilament you normally
use. For example, if you typically choose 8-lb. monofilament for applications,
you would want 30-lb. PowerPro.
Heavy Tackle Applications
If you normally fish using monofilament or Dacron lines of 50-lb. test or
greater, select a PowerPro line of the same test.
- Longer, Smoother Casts
- Better Handling on any Reel
- Superior Knot Performance
- Resists Burying in the Spool
- Near Zero Stretch
- Awesome Strength
How do I join my monofilament
backing to the Power Pro line?
Uni to Uni Splice
The best way to connect PowerPro to monofilament of similar diameter.
1) Pass the PowerPro and monofilament at least 12 to 18" past each other
so that loops can be formed. For a stronger knot, double the PowerPro.
2) Starting with the PowerPro, make 6 to 8 wraps through the loop and
pull to tighten. Do the same with the mono except 4 or 5 wraps are enough.
Pull on the tag end. Look to see that the wraps don't cross over each other.
3) Pull on the standing lines to jam the knots together. Trim.
